The boat is plastic for fishing. Can I make a plastic boat with my own hands?

Recently, the popularity ofuse a plastic boat for fishing. Alas, not everyone has the opportunity to acquire such a luxury. However, the output can be the manufacture of a vessel from improvised materials, to be more precise, from ordinary plastic bottles. The creation of such a vessel takes a little time, and the process itself is quite simple.

Why from bottles

Each can be created a plastic boatown hands. For this, it is not necessary to have a great deal of knowledge in shipbuilding. It is enough to follow certain rules. Of course, you can make a boat out of plywood or wood, but this is a very costly business. And not only in terms of finance. Plastic bottles are much cheaper. In principle, they can even be collected by placing a special container in a public place. In addition, the construction of a boat from this material is much easier.

It should be noted that for the manufacture of products fromwood or plywood is required to carry out special calculations. Otherwise, the ship simply will not stay on the water or be in it will be very dangerous.

We collect all necessary

To get a good plastic boat forfishing, you need to collect a huge number of plastic bottles of large volume and prepare additional tools. Such a container for the creation of a design will go much less, and the assembly process will proceed faster and easier. So, to make a boat you need a wide scotch, a well sharpened knife, large scissors, a hank of strong, but thin wire, cross-pieces made of sufficiently thick plywood, light pipes or boards.

In addition, you can select the material thatwill serve for the final finishing. If desired, the finished product can be sewed with thick plywood or any other dense, but light material. After this, the boat can be painted with a waterproof coating. This will make the design more neat and beautiful. You can even stick your logo on the boat.

Preparing bottles

So, how to properly build a plastic boatFor fishing? First you need to prepare the bottles. In order for the tanks to become more efficient and stiff, they should be pumped with air under pressure. Of course, at home it is difficult to do, but you can. It is enough to recall the simplest law of physics: when heated, any substance expands. This applies to air.

For this, plastic bottles must be placed infreezer, and then, tightly closing, remove. Once in heat, the air will begin to expand. Everything is simple enough. There will be an expansion of air due to a sharp temperature drop. As a result, the bottles will become more elastic and stiff. This is what is needed to create a more sustainable vessel on the water. Of course, if there is a possibility, it is better to pump the tanks with air under pressure.

Before use, plastic containers should beWash, remove all labels and labels, and then dry. If there are stains from the glue, they should also be removed. When twisting the cork from the bottles, it is best to put a good glue on the water resistant one. This will prevent their depressurization.

We produce logs

To make a boat plastic for fishing wellkept on the water, from the prepared material you need to collect improvised logs. This is done very simply. Two bottles must be connected with bottoms. In this case, the recesses of one container must fall into the recesses of the second one. You can attach the bottles to the third one. To do this, you need to cut the middle part of the container and put it on two fastened together.

After this, all places with joints should betreated with waterproof glue, preferably the most reliable, which is suitable for gluing plastic parts. And at the end we squeeze tape. It is very important. After all only in this case plastic rowing boats for fishing will last very long. Of course, if desired, this design can be equipped with a motor.

Now you need to take two bottles and cut them offbottoms. They put on the ends of the already finished part of the log. All joints again need to be smeared with glue and wrapped with scotch tape. As a result, the bottoms are formed at the ends of the workpiece. Now the log is assembled according to the same principle as described above.

Floats from logs

Even plastic boats for the engine are madefrom the floats. To do this, the finished logs must be firmly connected with each other. Thus in one float there can be up to eight designs. This is the most optimal number of logs. Of course, this indicator depends on the size and depth of the future ship. The main thing is to calculate everything correctly. In a ready boat, a person should feel comfortable.

The fastening of logs in this case is carried outwith the help of a thin, but strong enough wire, a polyethylene film and water-resistant tape. If desired, you can use glue, which is not afraid of moisture.

Picking up the boat

To plastic motor boats for fishing werestrong, you should carefully consider the assembly of the vessel. Of the ready floats it is necessary to collect something like a raft or a catamaran. If the design provides a motor, then it is better to make a ship in the form of a real boat or even a yacht. All, of course, depends on the number of plastic bottles and needs.

Between the floats can be combined with,for example, cross bars. This part of the vessel is made of wooden bars, metal pipes or plywood. To the prepared cross-members, you can attach the bottom of the future vessel. It can also be a plain board, plywood or metal pipes. It all depends on the size of the boat and the number of people who will swim on it.

The final stage

In principle, the boat is almost ready. It remains only to improve its appearance. If desired, it is possible to sew the side parts and the stern with waterproof material, multilayer plywood. And then just paint in the right color.

In this plan there are no restrictions. In addition, plastic boats for a motor can be made. Of course, do not weight the design. It remains to install the motor. This is very important if the product is designed for a large number of people and has considerable dimensions.