Why does not the water come up with a washing machine? Causes

Modern washing machines arecomplex devices that have a number of additional functions and modes designed to perform a variety of tasks to facilitate the work of their hosts. In this case, this technique has a lot of protective systems, protecting it from damage or violations in the technical process. In view of this, even the smallest breakdown can cause the user to have difficulty operating and usually leads to the call of the wizard, which is directly related to additional costs. However, if a washing machine does not pick up water, then sometimes it is enough to perform certain actions or to perform self-repair in order to save money and not contact the service center for details.

Types of breakdowns and their elimination

To begin with, it is worth mentioning that everythingThe following methods are suitable for almost all models of this technique. These are the simplest manipulations that can be made independently without dismantling the unit and without special education. When the washing machine does not pick up water and everything described below does not help to fix the problem, it is worth to contact the service center.

No water in the system

This reason is trivial, but beforeall worth checking is it. The fact is that many housewives are sometimes so carried away by domestic concerns that sometimes they forget that this product needs to be recharged from the water supply system. Therefore, if the washing machine does not pick up water, then try to open the tap and make sure that it is in your apartment. This behavior of the device is possible with a small head.

The crane is blocked

Very often when connecting such devices toA special faucet is installed in the water pipe, which blocks the access of the liquid to the unit. Sometimes it is practically not used and its existence is simply forgotten. As a result, if you block it, you can immediately not guess the reason for this behavior of the device. Therefore, if the washing machine does not collect water, then it is worth checking this locking mechanism and, if necessary, putting it into the open position.

Breach in the process

Sometimes this technique often behavesit's strange if there was a mistake in the program. When the washing machine picks up and drains the water before the washing starts, then this can refer specifically to this type of mismatch. What to do:

• First of all, pay attention to the presence of laundry in the drum. Some models in the absence of it can either not gain liquid at all, or immediately drain it.
• Sometimes such a defect arises already in the process itselfwashing, which is usually associated with a large weight of the laundry itself or its uneven distribution. Modern technology is equipped with just a huge number of sensors that control the whole process.
• Individual models control the closing of the loading door and even the tray into which the powder is poured. Therefore, it is worth checking the tightness of their adhesion to the body.

Such violations in the process usually have their own error code and are often displayed on the device's working panel. Some manufacturers give the decoding of these signals in the instruction manual.

Door failure

If the washing machine does not pick up water, the reasonsThis behavior is most often associated with a disruption in the operation of the door. The fact is that a special sensor is installed on its lock, and if it does not work properly or fails, then there will not be a supply of liquid. It is worth noting that the replacement of such a part is quite simple, and in some models it can be performed without disassembling the device. Very often, users simply remove the sensor itself, closing its contacts, but then the lock stops holding the door, which can lead to its spontaneous opening during spinning, when the vibration increases.

Filter clogging

If you are wondering whywashing machine is not taking on water, should take into account the specific structural features of the model. The fact is that at the entrance to the feeder system very often set small filter in the form of a metal mesh. It must be periodically cleaned:

• First disconnect the machine hose from the water supply. This may require a key, since the hose is connected through a special coupling.
• At one end of the connection pipe, a filter is usually installed. It must be cleaned.
• In some cases, the metal mesh rusts and completely fails. In this case, it must be replaced.
• At the end of the work, it is necessary to assemble the system back by connecting the hose to the water supply.

Damage to the intake valve

If the washing machine "Indesit" does not gainwater, sometimes the reason for the malfunction of the special intake valve, which is located at the entrance to the device. A similar defect is inherent in aggregates and from other manufacturers, since this element is common for all products of this type. It should be noted that its design is designed in such a way that if it fails, it switches to the "locked" position to prevent flooding.

Independently to eliminate such a breakdown quitecomplicated. To do this, you have to disassemble the device, disconnect this node from the water supply system and disconnect the controller contacts from it. After that, the valve is removed and replaced. Elimination of such a malfunction can be attributed to minor repairs, although its cost directly depends on the price of the necessary part.

Pump failure

Diagnose a similar fault canonly a master. However, if the tank itself is full, no pumping is performed and no water is supplied, this is the first sign of such a malfunction. In this case, it is first necessary to check the filter of the device, since if it is clogged, then the liquid can not be removed. If the cleaning does not bring the result, you need to contact the service center.

Replacement of this node can be quite expensive,therefore, it is very important to take care of the product during operation. It is necessary to periodically clean the filter and install a drain hose at the level recommended by the instruction.

Defective programmer

Modern household appliances for this purposeequipped with a fairly sophisticated electronics that controls the entire process. Therefore, if it fails or it breaks down, then just the washing machine does not gain water. What to do in such cases, usually indicated in the operating instructions for a particular model. However, there are also simple actions that you can do yourself:

• First of all, a breakdown of this type is displayed on the display panel of the device. It can look like an error, an incorrect label or a complete absence of an indication. This is how the defect is determined.
• Next, disconnect the device from the mains and leave in this position for 10-15 minutes. After this, the inclusion is made.
• If after such actions the machine did not work,it is recommended to call the wizard. It is rather difficult to repair this mechanism independently, especially if there is no special tool, there is no appropriate education and spare parts.

Problems in the pressure sensor

This site is designed toto monitor the supply of water to the machine. It is he who is responsible for the amount of liquid in accordance with the weight of the laundry. Therefore, if there is a breakdown in it, the water simply will not enter the device. The replacement of this part is carried out with the help of specialists of the service center, where it is almost always available.

It is better not to carry out such repair yourself. The matter is that in some models it is necessary to make the subsequent adjustment or updating, and for this purpose it is necessary to have the corresponding equipment.

Recommendations of specialists

• If the washing machine picks up water and immediatelydraining it, you should pay attention to the washing mode, which is set on the programmer. Quite often housewives simply forget that they have chosen a certain way of accomplishing the task, which presupposes this behavior. That's why experts recommend checking at the optimal mode.
• If the product is under warranty, it is not necessaryindependently disassemble it and replace certain nodes. The call of a qualified specialist will take some time, but it will save a considerable amount.
• Sometimes in the instruction manual in detaildescribes the sequence of actions when a certain fault is detected. All instructions should be performed clearly and in the order given, as they are written for a specific model, taking into account its technical features and test tests.
• If the hose of the device is disconnected from the water supply system, it is necessary to shut off the liquid supply in this section or completely in the network.
• On some models, the operation of the intake valve is checked by switching the machine on. If this node is functional, a characteristic click must be heard, caused by the temporary opening of the valve.

Conclusion

If the washing machine does not pick up water, thenThere are many reasons for this behavior in this device. That is why, before you contact specialists, you need to completely eliminate the influence of the human factor, so as not to spend money on repairs and do not look stupid before the master, who discovered that you just blocked the intake valve. In this case, most of the failures associated with such a violation in the work, you can eliminate yourself without having to dismantle the machine.